Where the register points next
training.gov.au points at nothing after MEM31419: it is the current product, and no replacement is listed.
What the register says changed
These are the mapping notes training.gov.au attaches to each supersession, quoted as the register writes them. They are the only public record of what actually changed between two versions.
Is MEM31419 on your scope?
This page is the register's record of one product. What it cannot tell you is whether MEM31419 sits on your own scope today, or what else on that scope has moved without anyone noticing. Enter your RTO number and we read every product on your live scope against training.gov.au and tell you which ones are superseded and which replacements the register flags not equivalent.
Whether a supersession requires anything of you, and what, sits with you and your regulator. This page maps what the register records; it does not make that judgement. If the difference between an equivalent and a non-equivalent replacement is the question, we wrote it up in equivalent vs not equivalent.
What MEM31419 is made of
training.gov.au lists 71 units for MEM31419: 19 core and 52 elective. The register does not publish a completion rule in units for this product, so we do not state one. How many of the electives are required is in the packaging rules on training.gov.au.
Core units 19 listed
| Code | Unit | In this product |
|---|---|---|
| MEM09002 | Interpret technical drawing | ●current |
| MEM11011 | Undertake manual handling | ●current |
| MEM12023 | Perform engineering measurements | ●current |
| MEM12024 | Perform computations | ●current |
| MEM13015 | Work safely and effectively in manufacturing and engineering | ●current |
| MEM14006 | Plan work activities | ●current |
| MEM16006 | Organise and communicate information | ●current |
| MEM16008 | Interact with computing technology | ●current |
| MEM17003 | Assist in the provision of on-the-job training | ●current |
| MEM18001 | Use hand tools | ●current |
| MEM18002 | Use power tools/hand held operations | ●current |
| MEM18055 | Dismantle, replace and assemble engineering components | ●current |
| MEM27006 | Diagnose and rectify batteries, low voltage sensors and circuits | ●current |
| MEM27016 | Diagnose and maintain electronic controlling systems on mobile and stationary plant | ●current |
| MEM27017 | Maintain, fault find and rectify hydraulic systems for mobile plant | ●current |
| MEM27019 | Diagnose, repair and replace diesel engines in stationary and mobile plant | ●current |
| MEM27020 | Apply knowledge of large combustion engine operations to service and maintenance tasks | ●current |
| MEM27023 | Diagnose and rectify fieldbus circuits in mobile and stationary plant and equipment | ●current |
| MSMENV272 | Participate in environmentally sustainable work practices | ●current |
Elective units 52 listed
| Code | Unit | In this product |
|---|---|---|
| CPPFES2027 | Inspect, test and maintain non-gaseous pre-engineered fire-suppression systems | ●current |
| CPPFES3042 | Install and commission pre-engineered fire-suppression systems | ●current |
| MEM05001 | Perform manual soldering/desoldering - electrical/electronic components | ●current |
| MEM05002 | Perform high reliability soldering and desoldering | ●current |
| MEM05007 | Perform manual heating and thermal cutting | ●current |
| MEM05012 | Perform routine manual metal arc welding | ●current |
| MEM05049 | Perform routine gas tungsten arc welding | ●current |
| MEM05050 | Perform routine gas metal arc welding | ●current |
| MEM07005 | Perform general machining | ●current |
| MEM10002 | Terminate and connect electrical wiring | ●current |
| MEM12002 | Perform electrical/electronic measurement | ●current |
| MEM13001 | Perform emergency first aid | ●current |
| MEM13019 | Undertake work health and safety activities in the workplace | ●current |
| MEM18003 | Use tools for precision work | ●current |
| MEM18005 | Perform fault diagnosis, installation and removal of bearings | ●current |
| MEM18006 | Perform precision fitting of engineering components | ●current |
| MEM18008 | Balance equipment | ●current |
| MEM18009 | Perform precision levelling and alignment of machines and engineering components | ●current |
| MEM18012 | Perform installation and removal of mechanical seals | ●current |
| MEM18013 | Perform gland packing | ●current |
| MEM18018 | Maintain pneumatic system components | ●current |
| MEM18019 | Maintain pneumatic systems | ●current |
| MEM18020 | Maintain hydraulic system components | ●current |
| MEM18021 | Maintain hydraulic systems | ●current |
| MEM18022 | Maintain fluid power controls | ●current |
| MEM18049 | Disconnect/reconnect fixed wired equipment up to 1000 volts a.c./1500 volts d.c. | ●current |
| MEM18050 | Disconnect/reconnect fixed wired equipment over 1000 volts a.c./1500 volts d.c. | ●current |
| MEM27001 | Maintain and repair stationary and mobile plant engine cooling systems | ●current |
| MEM27002 | Test and repair compression ignition systems | ●current |
| MEM27003 | Overhaul engine fuel system components | ●current |
Show the remaining 22 elective units
| Code | Unit | In this product |
|---|---|---|
| MEM27004 | Maintain and repair engine lubrication systems | ●current |
| MEM27005 | Tune diesel engines | ●current |
| MEM27007 | Diagnose and rectify low voltage starting systems | ●current |
| MEM27008 | Maintain induction, exhaust and emission control systems | ●current |
| MEM27009 | Diagnose and rectify braking systems | ●current |
| MEM27010 | Diagnose and rectify low voltage charging systems | ●current |
| MEM27011 | Maintain track type undercarriage on mobile plant | ●current |
| MEM27012 | Maintain mobile plant suspension systems | ●current |
| MEM27013 | Maintain steering systems | ●current |
| MEM27014 | Diagnose and rectify automatic transmissions | ●current |
| MEM27015 | Diagnose and rectify drive line and final drives | ●current |
| MEM27021 | Maintain, fault find and repair stationary plant gas turbine engines | ●current |
| MEM27022 | Maintain, fault find and repair traction drive mechanics | ●current |
| MEM27026 | Service and repair mobile plant air conditioning systems | ●current |
| MEM27028 | Diagnose and rectify manual transmissions | ●current |
| MEM27029 | Maintain wheels and tyres | ●current |
| MEM27030 | Perform engine bottom-end overhaul | ●current |
| MEM27031 | Perform engine top-end overhaul | ●current |
| MEM27032 | Service combustion engines | ●current |
| MSMENV472 | Implement and monitor environmentally sustainable work practices | ●current |
| TLILIC0003 | Licence to operate a forklift truck | ●current |
| TLILIC0024 | Licence to operate a vehicle loading crane (capacity 10 metre tonnes and above) | ●current |
Core and elective are the register's own flags on the unit grid of the release read here. "Not current" means training.gov.au no longer recommends that unit for use inside this product — it does not say anything about the product itself.
Source: this product on training.gov.au, Australia's national training register — or go straight to the units it requires. The rule itself is item 14 of F2025L00355, and ASQA publishes the extensions it has granted. Read on 28 August 2026 UTC. Every code, title, date, status and equivalence flag on this page is the register's; nothing here is estimated or inferred, and where the register publishes nothing we say so.
Every MEM training product on the register · Search all training products
Deliver this? We read the register nightly — get the free breakdown of your whole scope, and hear the day MEM31419 or anything else on it is superseded.
No account, no card. We never ask for anything about your learners. Your address gets this one report — no list, no marketing — and the scope watch only if you tick the box, with one click to stop it.