MSFFM3011 Measure and draw site layout for manufactured furniture products

Supersededtraining.gov.au: supersededNonEquivalent

The currency period for MSFFM3011 ended on 6 December 2022 — 3 years ago. It names one replacement below, with the equivalence it declares for each.

Transition clockClosed to new enrolments

New enrolments are not permitted from 8 December 2023 — one year from the date the replacement was included on the National Register (s 14(1)(a)(i) of the National VET Regulator (Compliance Standards for NVR RTOs and Fit and Proper Person Requirements) Instrument 2025 (F2025L00355, in force 1 July 2025)), or from a later date if ASQA has approved otherwise for your organisation.

Learners already enrolled have no fixed deadline: they complete the product and are issued their AQF certification, or transfer to the replacement, in a timely manner (ASQA guidance, read live 25 August 2026).

The same date closes a second obligation: under s 7(2)(c) of the same instrument, advertising may refer to a superseded product only while it is on scope and new enrolments are permitted. When enrolments stop, the course page advertising it stops being permitted too — and if ASQA approves a later enrolment date, that moves with it.

Sector-wide: the item 14 cut-off, measured across every live scope · the repealed 12-month rule

Product type
Unit of competency
Training package
MSF — Furnishing Training Package
Currency period ends
6 December 2022
Latest release
Release 1 · 10 December 2013
Supersedes
LMFFM3013B
Superseded by
MSFFM3041 not equivalent

Where the register points next

Each step below is one supersession training.gov.au publishes between two products. The label on the rail is the equivalence the register declares for that step — not our reading of it.

  1. MSFFM3011Superseded — not equivalentMeasure and draw site layout for manufactured furniture products
  2. not equivalent
  3. MSFFM3041CurrentDetermine and document requirements for cabinetry installation

What the register says changed

These are the mapping notes training.gov.au attaches to each supersession, quoted as the register writes them. They are the only public record of what actually changed between two versions.

  • LMFFM3013BMSFFM3011equivalent9 December 2013

    The register records this supersession but attaches no note on what changed.

  • MSFFM3011MSFFM3041not equivalent7 December 2022

    The register records this supersession but attaches no note on what changed.

Is MSFFM3011 on your scope?

This page is the register's record of one product. What it cannot tell you is whether MSFFM3011 sits on your own scope today, or what else on that scope has moved without anyone noticing. Enter your RTO number and we read every product on your live scope against training.gov.au and tell you which ones are superseded and which replacements the register flags not equivalent.

Public code, nothing else. We read your live scope from training.gov.au and answer here — nothing is stored unless you ask us to watch it.

Whether a supersession requires anything of you, and what, sits with you and your regulator. This page maps what the register records; it does not make that judgement. If the difference between an equivalent and a non-equivalent replacement is the question, we wrote it up in equivalent vs not equivalent.

Where MSFFM3011 is used

training.gov.au lists MSFFM3011 inside 12 training products, 3 of them current. Every one of them is below, with the register's own core or elective flag for MSFFM3011 in that product.

Current products 3 listed

CodeTraining productTypeMSFFM3011 is
CPC30120Certificate III in ShopfittingQualificationelective
CPC31920Certificate III in JoineryQualificationcore
MSF40318Certificate IV in Kitchen and Bathroom DesignQualificationcore

Products no longer current 9 listed

The register still records MSFFM3011 inside these, but it no longer recommends them as current. They are here because a scope history or an old enrolment can still point at them.

CodeTraining productTypeMSFFM3011 is
CPC30116Certificate III in ShopfittingQualificationelective
MSF30213Certificate III in Furniture MakingQualificationelective
MSF30313Certificate III in Timber and Composites MachiningQualificationelective
MSF31113Certificate III in Cabinet MakingQualificationelective
MSF40313Certificate IV in Design of Kitchens, Bathrooms and Interior SpacesQualificationcore
MSFSS00004Kitchen and Bathroom Installer LicenseSkill setelective
MSFSS00006Fitted Furniture EstimatorSkill setelective
MSFSS00011Kitchen and Bathroom Installer LicenseSkill setelective
MSFSS00012Fitted Furniture EstimatorSkill setelective

Source: this product on training.gov.au, Australia's national training register — or go straight to the units it requires. The rule itself is item 14 of F2025L00355, and ASQA publishes the extensions it has granted. Read on 28 August 2026 UTC. Every code, title, date, status and equivalence flag on this page is the register's; nothing here is estimated or inferred, and where the register publishes nothing we say so.

Every MSF training product on the register · Search all training products

Is MSFFM3011 still on your scope? Type your RTO code and get the free breakdown — every superseded product on your live scope, and whether the register flags each replacement equivalent.

No account, no card. We never ask for anything about your learners. Your address gets this one report — no list, no marketing — and the scope watch only if you tick the box, with one click to stop it.