CPCCCM3001C Operate elevated work platforms

Supersededtraining.gov.au: supersededEquivalent

The currency period for CPCCCM3001C ended on 7 September 2016 — 10 years ago. It names one replacement below, with the equivalence it declares for each.

Transition clockOpen for new enrolmentsClosing to new enrolments soonClosed to new enrolments

For an RTO registered by ASQA, new enrolments are not permitted today, unless ASQA has approved otherwise — for your organisation, for a class of RTOs, or for all RTOs. The one-year point this rule counts from — one year from the date the replacement was included on the National Register — fell earlier, on 9 September 2017. That date is arithmetic, not a day on which this instrument prohibited anything: s 14(1)(a)(i) of the National Vocational Education and Training Regulator (Compliance Standards for NVR Registered Training Organisations and Fit and Proper Person Requirements) Instrument 2025 (F2025L00355) commenced on 1 July 2025 and imposes nothing before then. RTOs registered by VRQA in Victoria or by the TAC in Western Australia are not covered by it.

Learners already enrolled have no fixed deadline: they complete the product and are issued their AQF certification, or transfer to the replacement, in a timely manner (ASQA guidance, read live 25 August 2026).

A second obligation follows from the same fact: under s 7(2)(c) of the same instrument, advertising may refer to a superseded product only while it is on scope and new enrolments are permitted. For an RTO registered by ASQA, new enrolments in this product are not permitted today, so a course page advertising it is not permitted either — and if ASQA approves a later enrolment date, that moves with it.

Sector-wide: the item 14 cut-off, measured across every live scope · the repealed 12-month rule

Product type
Unit of competency
Training package
CPC08 — Construction, Plumbing and Services Training Package
Currency period ends
7 September 2016
Latest release
Release 1 · 7 February 2013
Supersedes
CPCCCM3001B
Superseded by
CPCCCM3001 equivalent

Where the register points next

Each step below is one supersession training.gov.au publishes between two products. The label on the rail is the equivalence the register declares for that step — not our reading of it.

  1. CPCCCM3001CSuperseded — equivalentOperate elevated work platforms
  2. equivalent
  3. CPCCCM3001CurrentOperate elevated work platforms up to 11 metres

What the register says changed

These are the mapping notes training.gov.au attaches to each supersession, quoted as the register writes them. They are the only public record of what actually changed between two versions.

  • CPCCCM3001BCPCCCM3001Cequivalent6 February 2013

    Prerequisite unit identifer updated. Equivalent to CPCCCM3001B

  • CPCCCM3001CCPCCCM3001equivalent8 September 2016

    Revised unit of competency. Replaces superseded equivalent CPCCCM3001C Operate elevated work platforms.

Official documents on the register

What training.gov.au lists for CPCCCM3001C and for its training package CPC08 (release 9.9), with the name and date the register publishes for each file. We link them; we have not read them, and nothing on this page is taken from their contents.

Is CPCCCM3001C on your scope?

This page is the register's record of one product. What it cannot tell you is whether CPCCCM3001C sits on your own scope today, or what else on that scope has moved without anyone noticing. Enter your RTO number and we read every product on your live scope against training.gov.au and tell you which ones are superseded and which replacements the register flags not equivalent.

Public code, nothing else. We read your live scope from training.gov.au and answer here — we keep neither the code nor the answer; what remains is the two-minute abuse counter described on our privacy page.

Whether a supersession requires anything of you, and what, sits with you and your regulator. This page maps what the register records; it does not make that judgement. If the difference between an equivalent and a non-equivalent replacement is the question, we wrote it up in equivalent vs not equivalent.

Where CPCCCM3001C is used

training.gov.au lists CPCCCM3001C inside 41 training products, none of them current. Every one of them is below, with the register's own core or elective flag for CPCCCM3001C in that product.

Products no longer current 41 listed

The register still records CPCCCM3001C inside these, but it no longer recommends them as current. They are here because a scope history or an old enrolment can still point at them.

CodeTraining productTypeCPCCCM3001C is
AHC20510Certificate II in ArboricultureQualificationelective
AHC20513Certificate II in ArboricultureQualificationelective
AHC20516Certificate II in ArboricultureQualificationelective
AHC30810Certificate III in ArboricultureQualificationelective
CPC20812Certificate II in Metal Roofing and CladdingQualificationcore
CPC30111Certificate III in Bricklaying/BlocklayingQualificationelective
CPC30211Certificate III in CarpentryQualificationelective
CPC30411Certificate III in DemolitionQualificationelective
CPC30511Certificate III in DoggingQualificationelective
CPC30611Certificate III in Painting and DecoratingQualificationelective
Show the remaining 31 products no longer current
CodeTraining productTypeCPCCCM3001C is
CPC30711Certificate III in RiggingQualificationcore
CPC30812Certificate III in Roof TilingQualificationelective
CPC30911Certificate III in ScaffoldingQualificationelective
CPC31011Certificate III in Solid PlasteringQualificationelective
CPC31211Certificate III in Wall and Ceiling LiningQualificationelective
CPC31311Certificate III in Wall and Floor TilingQualificationelective
CPC31411Certificate III in Construction WaterproofingQualificationelective
CPC31511Certificate III in Formwork/FalseworkQualificationelective
CPC31712Certificate III in Post-TensioningQualificationelective
CPC31812Certificate III in ShopfittingQualificationelective
CPC32011Certificate III in Carpentry and JoineryQualificationelective
CPC32111Certificate III in SignageQualificationelective
CPC32311Certificate III in Stonemasonry (Monumental/Installation)Qualificationelective
CPC32313Certificate III in Stonemasonry (Monumental/Installation)Qualificationelective
CPC32412Certificate III in PlumbingQualificationelective
CPC32413Certificate III in PlumbingQualificationelective
CPC32512Certificate III in Plumbing (Mechanical Services)Qualificationelective
CPC32513Certificate III in Plumbing (Mechanical Services)Qualificationelective
CPC32612Certificate III in Roof PlumbingQualificationcore
CPC32712Certificate III in Gas FittingQualificationelective
CPC32713Certificate III in Gas FittingQualificationelective
CPC32812Certificate III in Fire ProtectionQualificationelective
CPC32813Certificate III in Fire ProtectionQualificationelective
CPC32912Certificate III in Construction Crane OperationsQualificationcore
CUA20213Certificate II in Live Production and ServicesQualificationelective
CUA20215Certificate II in Creative IndustriesQualificationelective
CUA30413Certificate III in Live Production and ServicesQualificationelective
CUA30415Certificate III in Live Production and ServicesQualificationelective
CUA40413Certificate IV in Live Production and Technical ServicesQualificationelective
CUA40415Certificate IV in Live Production and Technical ServicesQualificationelective
MSF30913Certificate III in Blinds, Awnings, Security Screens and GrillesQualificationelective

Source: this product on training.gov.au, Australia's national training register — or go straight to the units it requires. The rule itself is item 14 of F2025L00355, and ASQA publishes the extensions it has granted. Read on 14 October 2026 UTC. Every code, title, date, status and equivalence flag on this page is the register's; nothing here is estimated or inferred, and where the register publishes nothing we say so.

Every CPC training product on the register · Search all training products

Take this with you — one email with this page's clock as the register states it today. Nothing scheduled after it.

No account, no card. Your address gets this one email — no list, no marketing. Cutoff alerts only ever come from a watch you start yourself — the box just records your yes now — and every alert has a one-click stop.

Is CPCCCM3001C still on your scope? Type your RTO code and get the free breakdown — every superseded product on your live scope, and whether the register flags each replacement equivalent.

No account, no card. We never ask for anything about your learners. Your address gets this one report — no list, no marketing — and the scope watch only if you tick the box, with one click to stop it.